THE LARGEST BMW 2-SERIES FORUM ON THE PLANET
2Addicts
2Addicts
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read
2Addicts | BMW 2-Series forum Technical Topics Cosmetic and Lighting Modifications DIY: Adding more Ambient lighting, the OEM way

Post Reply
 
Thread Tools Search this Thread
      11-18-2020, 09:12 AM   #1
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

DIY: Adding more Ambient lighting, the OEM way

I'm going to have a try at adding more ambient lighting to my BMW F20 LCI. I'm posting it here since the F20 forums are dead and a mess and because this will be compatible with practically any BMW.
I'm going to document my journey as best I can here.
My car is equipped from factory with the Extended Lighting Package. Basically it means I have the lights on the door handles on the exterior and dual colour (white and orange) ambient lighting on the interior. Now, I find that the number of lighting modules is insufficient to have a nice effect while driving at night. The only lighting modules I've got with ambient lighting are:
  • Lights in the footwell which are barely visible (even on full brightness)
  • Tiny "dots" on the headliner lighting units front and back
  • Front only door handle lighting units

I don't want to mess around with ambient lighting kits that may or may not work or look like a giant ricer with RGB lighting on my interior. That's why I'm going the OEM route. Everything is then accessible through the iDrive and it looks like it's always meant to be there. Also, I don't back away from a challenge and I want to try and figure out if everything I want is possible.

Lights to be retrofitted:
  • Door handle ambient lighting for rear passengers
  • Center console (cup holder) ambient lighting. The hole for this LED module is already present, but there is no module installed. Why, you ask? I have no clue.
  • Ground lights for rear passengers
  • I'll also try and have ambient lighting by means of optical wire on the door cards and dashboard trim. (More updates when I can see if worth it or not)

Parts needed: (will update as project comes along)
  • 51417274489 Door handle opener trim
  • 51417274490 Door handle opener trim
  • 2X 63319237712 Door handle opener LED Module F2X
  • 63319242162 LED Module center console
  • 2X 63317941911 LED Door module for ground lights (I already had 63319270505 which I replaced with BMW Door projectors, no longer produced)

Once I know all the correct pin numbers and part numbers for the door connector terminals, I'll update everything accordingly.

Research
I know almost all lighting is handled through the FEM (Front Electronics Module). I had a litte look around on the interior lighting wiring diagram on newTIS for my car and found the following:
  • The ambient lighting modules have 3 pins. A brown for ground and a white/red and white/blue cable to switch between the orange "classic" mode and the white "sport" mode. Those 2 last ones are connected to the FEM via plug A173*9B on pins 51 and 50 respectively. All ambient lighting modules branch from those 2 connections so to add other ones is as simple as creating more branches as needed. I don't worry about blowing a fuse since those modules are all LED and draw little current, also there are models like the F30 that have many more ambient lighting modules installed from factory connected to the same pins on the FEM.
  • For connecting the rear puddle or ground lights I've had a look at the wiring diagram of a F30. On the diagram you can see that the ground lights for the front are connected to pin 54 of the same A173*9B connector on the FEM as the ambient lights. That's also the case for the F20 FEM. Pin 53 is used for the rear ones, so that's what I'm going to do on the F20.
  • Connecting the front ambient lights (with optical cable) is simple. I'm going to make a Y splitter cable that branches off the existing door handle ambient light to add another.
  • Connecting the rear ground and ambient lights is a little more challenging. You have 1 major obstacle in the way, and that is the door connectors X8*1B and X9*1B. In the F30, the ambient lighting is connected through pins 17 for white/red and pin 18 for white/blue. Pin 13 is used for the ground lights.

On further investigation, it became clear the car is already pre-wired in the rear for all the retrofits I'm planning of doing. The red/blue wire for the ground lighting is present on pin 13 and the white/red and white/blue wires for the ambient lighting are present on pins 17 and 18. However, these wires are only present on the inside portion of the wiring harness. No cables are attached to those pins in the door wiring harness. So, that has to be fabricated by me.
It's funny to me how the car comes pre wired for all the lights to be installed. It's like they did 90% of the work and the owner has to do the other 10%?


DIY: The work
Installing the Rear ground door lights
In comparison to the front door panels which are made of a foam type hard plastic or rubber material, the rear door panels are hard plastic. Good stuff for making holes!
I measured the LED module and I needed to make a hole about 16mm wide and 62mm long. I drew the shape on a piece of paper, cut it out with scissors and used glue stick to stick in in place on the inside of the door panel. I placed it on the most flat part of the underside of the panel I could find. That is in between the 2 Torx screws, closest to the most inside, towards the body of the car, screw when you look at the doorpanel with the door open.
The panel also has these "supports" on the inside to make the plastic more rigid. One of them have to be trimmed as the space in between these supports is insufficient to fit the LED Module. It's an easy job with an exacto knife or box cutter.
Remember to make the hole a little undersize. You can always take more material away. Trust me. I learned it the hard way and cut 1 hole too big. One module is now held into place with superglue.
I'd recommend using a dremel tool with a cutting disc attachment to make the hole. Try not to hold the disc in the same place too long or forcing the disc in all the way in one go. This might melt the plastic making a not so nice looking hole.
When you're finished, the result should look something like this:



Installing Center Console Light
As mentioned in the introduction of this article, there's already an existing hole in the center console trim underneath the climate and radio controls for mounting this light, but there is none there. The purpose of this light is to illuminate the cup holders.
Installing the light is as simple as taking out the center console trim and sliding in the light until it clicks. Mine has as part no. 51459211304 but I can't seem to find any mention of this part on realOEM, instead they give you 51459236581 which appears to be the same part.
When the light is installed it should look like this:




Installing the Door Handle Lights
When you have the rear door cards removed, you can clearly see everything is already there to accommodate the same lighting modules as the fronts have. Why BMW didn't bother with putting them in is really above me. These modules seem to be the same as the center console one, only with a different face plate and double the price...
To install: just slide them in and watch out not to break the optical plastic light tube.

Last edited by Beau2795; 11-20-2020 at 07:19 AM..
Appreciate 0
      11-18-2020, 01:07 PM   #2
NewWorldOrder
Private
23
Rep
55
Posts

Drives: 2018 BMW M240ix vert
Join Date: Sep 2020
Location: Portland, Oregon

iTrader: (0)

Quote:
Originally Posted by Beau2795 View Post
I'm going to have a try at adding more ambient lighting to my BMW F20 LCI. I'm posting it here since the F20 forums are dead and a mess and because this will be compatible with practically any BMW.
I'm going to document my journey as best I can here.
My car is equipped from factory with the Extended Lighting Package. Basically it means I have the lights on the door handles on the exterior and dual colour (white and orange) ambient lighting on the interior. Now, I find that the number of lighting modules is insufficient to have a nice effect while driving at night. The only lighting modules I've got with ambient lighting are:
  • Lights in the footwell which are barely visible (even on full brightness)
  • Tiny "dots" on the headliner lighting units front and back
  • Front only door handle lighting units

I don't want to mess around with ambient lighting kits that may or may not work or look like a giant ricer with RGB lighting on my interior. That's why I'm going the OEM route. Everything is then accessible through the iDrive and it looks like it's always meant to be there. Also, I don't back away from a challenge and I want to try and figure out if everything I want is possible.

Lights to be retrofitted:
  • Door handle ambient lighting for rear passengers
  • Center console (cup holder) ambient lighting. The hole for this LED module is already present, but there is no module installed. Why, you ask? I have no clue.
  • Ground lights for rear passengers
  • I'll also try and have ambient lighting by means of optical wire on the door cards and dashboard trim. (More updates when I can see if worth it or not)

Parts needed: (will update as project comes along)
  • 51417274489 Door handle opener trim
  • 51417274490 Door handle opener trim
  • 2X 63319237712 Door handle opener LED Module F2X
  • 63319242162 LED Module center console

Research
I know almost all lighting is handled through the FEM (Front Electronics Module). I had a litte look around on the interior lighting wiring diagram on newTIS for my car and found the following:
  • The ambient lighting modules have 3 pins. A brown for ground and a white/red and white/blue cable to switch between the orange "classic" mode and the white "sport" mode. Those 2 last ones are connected to the FEM via plug A173*9B on pins 51 and 50 respectively. All ambient lighting modules branch from those 2 connections so to add other ones is as simple as creating more branches as needed. I don't worry about blowing a fuse since those modules are all LED and draw little current, also there are models like the F30 that have many more ambient lighting modules installed from factory connected to the same pins on the FEM.
  • For connecting the rear puddle or ground lights I've had a look at the wiring diagram of a F30. On the diagram you can see that the ground lights for the front are connected to pin 54 of the same A173*9B connector on the FEM as the ambient lights. That's also the case for the F20 FEM. Pin 53 is used for the rear ones, so that's what I'm going to do on the F20.
  • Connecting the front ambient lights (with optical cable) is simple. I'm going to make a Y splitter cable that branches off the existing door handle ambient light to add another.
  • Connecting the rear ground and ambient lights is a little more challenging. You have 1 major obstacle in the way, and that is the door connectors X8*1B and X9*1B. In the F30, the ambient lighting is connected through pins 17 for white/red and pin 18 for white/blue. Pin 13 is used for the ground lights.
Once I know all the correct pin numbers and part numbers for the door connector terminals, I'll update everything accordingly.
This is something I'd seriously be interested in. Will be following the thread.
Appreciate 0
      11-18-2020, 01:43 PM   #3
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

EDIT 18/11/2020 19:40

I've started with the DIY job. First on the list: Rear ground lights. I've updated my first post.
Question to those interested: would you like me to add everything in my first post by editing and telling you I made an edit or make multiple messages in this thread with progress in them?
Appreciate 0
      11-18-2020, 03:37 PM   #4
NewWorldOrder
Private
23
Rep
55
Posts

Drives: 2018 BMW M240ix vert
Join Date: Sep 2020
Location: Portland, Oregon

iTrader: (0)

Quote:
Originally Posted by Beau2795 View Post
EDIT 18/11/2020 19:40

I've started with the DIY job. First on the list: Rear ground lights. I've updated my first post.
Question to those interested: would you like me to add everything in my first post by editing and telling you I made an edit or make multiple messages in this thread with progress in them?
Probably best to just edit the post. Just in case the thread gets long.
Appreciate 0
      11-19-2020, 11:30 AM   #5
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

EDIT: 19/11/2020 17:27

Today, I received my first of a series of shipments for this project. Unfortunately no wiring supplies, yet, but that's on order and coming soon.
I installed the center console lighting module as well as the rear door handle modules. In the process I was able to break one of my new door handle trims
The small plastic optical lighting tubes that illuminate the door handle got stuck between the door panel and the trim piece and broke off. I have to order a new one of those unfortunately. Everything else went really smoothly and I cannot wait to see the end result!
Hope I can be helpful with this writeup!
Appreciate 0
      11-20-2020, 07:22 AM   #6
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

EDIT: 20/11/2020 13:20

Did some more digging today and found out the car is already pre-wired on the inside to accommodate all the lighting modifications I'm planning to do. This is great news because I won't have to tap into pre existing wiring and the result will look even more OEM! Only wiring harnesses will need to be made for the rear doors because the pre existing wires don't have a receiving end in the door wiring harness.
Appreciate 0
      11-20-2020, 11:49 PM   #7
celsdogg
E4 Mafia
United_States
78
Rep
192
Posts

Drives: E30, E36/5, F22, F30
Join Date: Apr 2018
Location: MD

iTrader: (0)

this is really cool, can't wait to see your progress!
__________________
Squad - E30 325i MT | E36/5 318ti MT | F22 M235i MT | F30 335i MT
KIA - E30 325i AT | E46 325i MT
Appreciate 0
      11-23-2020, 03:39 PM   #8
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

UPDATE: 23/11/2020 21:35

Today I had a go at making a harness for the rear doors. Everything plugged in fine, ambient lighting is working, but unfortunately I can't get a voltage for the rear ground lights. I will need to access the FEM, look at the wiring and try to see if I can get a voltage to pin 13 in the door connector. If not, maybe some coding needs to be done? I will keep this updated when I find out new information.
Appreciate 0
      11-23-2020, 07:38 PM   #9
NewWorldOrder
Private
23
Rep
55
Posts

Drives: 2018 BMW M240ix vert
Join Date: Sep 2020
Location: Portland, Oregon

iTrader: (0)

Well there isn't a hole for the center console light on the LCI f23. It also seems to be a part of the dash, so you'd have to take off the entire dash to get to it if there was one.

Maybe Pre LCI will be able to do this. They can take off that piece without having to take off the entire dash.
Appreciate 0
      11-24-2020, 04:13 AM   #10
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

Quote:
Originally Posted by NewWorldOrder View Post
Well there isn't a hole for the center console light on the LCI f23. It also seems to be a part of the dash, so you'd have to take off the entire dash to get to it if there was one.

Maybe Pre LCI will be able to do this. They can take off that piece without having to take off the entire dash.
Some F2X LCI models will have the dash I have. On my F20 LCI with build date 03/2016 I still have the "pre-lci" dash. On later build date models, they changed the dash to the one piece. Then the center console light retrofit will not work like you mentioned.
I never liked the shape of the one piece dashboards anyway so I'm glad. They look kinda cheap imho..
Appreciate 0
      11-25-2020, 10:15 AM   #11
Beau2795
Enlisted Member
6
Rep
45
Posts

Drives: 2016 F20 LCI 118d M Sport
Join Date: Feb 2016
Location: Belgium

iTrader: (0)

UPDATE 25/11/2020 16:12

Great success! Got everything working in one door. I will add a full writeup with pictures when I do the other door. As mentioned in the previous update: ambient lighting works as is, the ground light does not. After some digging in the FEM using Esys and on the forums I found this:
FEM_01 > LciConfiguration 3071 > MAPPING_LCI_4_FUNCTION = off
It needs to be changed to:
FEM_01 > LciConfiguration 3071 > MAPPING_LCI_4_FUNCTION = footwell_rear
Then pin 53 on the FEM gives the voltage to the door connector for the ground lights!
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 08:52 PM.




2addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST