05-28-2018, 01:09 AM | #1 |
Private
19
Rep 81
Posts |
Easy entry with bimmercode?
I have a 228i and I use Bimmercode to code my car on my android. I've done some searching but I haven't found an answer.. can you code easy entry on the Bimmercode app?
__________________
2014 228i M Sport w/ M235i Exhaust, VRSF DP, Stage 2 AA ODB2 Tune
|
05-29-2018, 06:29 PM | #2 |
Private First Class
43
Rep 121
Posts |
I have tried this with my 2018 230i without success. The values in the seat module are supposed to be:
3000 SM_GLOBAL ->*EINAUSSTIEGSHILFE*= Modus_FA_SLV 3012 EAH -> EAH_VERFAHRWEG_SLV_PHYS = Werte=00, 28 3012 EAH -> EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS = Werte=00, 3C For the last two parameters, however Bimmercode for Android only allows "initwerte." Perhaps it's different in the iPhone version. |
Appreciate
0
|
05-30-2018, 01:03 PM | #3 |
Enlisted Member
6
Rep 39
Posts |
I have coded my 2018 M240i for easy entry with bimmercode. I left the last two values at initwerte initially. Easy entry only worked for my GF and not me because I already had the seat too far back for the initial rear legroom limit. I had to go back with esys and change that last value to 00, 0F in order for easy entry to work. Hope this helps!
|
Appreciate
1
///M Houbi1672.00 |
05-30-2018, 01:26 PM | #4 |
Private First Class
43
Rep 121
Posts |
Do you remember if you had to code any other parameters? I also coded (in FEM):
30C0 EINSTIEGSH_LN_AKTIV set to: aktiv 30C0 EINSTIEGSH_NG_AKTIV set to: aktiv 30C0 PRIO_ACHSEN set to: 1 although these have to do with electric steering wheel adjustment, which I (we?) don't have. Couldn't get it to work. :-( |
Appreciate
0
|
05-30-2018, 11:45 PM | #5 | |
Enlisted Member
6
Rep 39
Posts |
Quote:
|
|
Appreciate
0
|
05-31-2018, 12:40 AM | #6 |
Luxury at the redline :)
9118
Rep 7,563
Posts |
You guys might screw up your ECU if you keep coding stuff randomly, that you're not sure about...
Here is the coding for 'Comfort Exit/Entry' The werte "64" = 100mm of retraction, lower the number from 64 or convert the hex value entry to decrease the retraction, if you please. I've done it on a couple of BMWs, it's guarantee to work. I'm not sure if it works for 2018 though, since some folks been having issues with the new MY and coding. Good luck. 19bis Driver Seat: 3000 SM_GLOBAL -> EINAUSSTIEGSHILFE = Modus_FA_SLV 3012 EAH -> EAH_VERFAHRWEG_SLV_PHYS = Werte=00, 64 3012 EAH -> EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS = Werte=00, 00 Passenger Seat: 3000 SM_GLOBAL -> EINAUSSTIEGSHILFE = UKNOWN, WERTE=03 3012 EAH -> EAH_VERFAHRWEG_SLV_PHYS = Werte=00, 64 3012 EAH -> EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS = Werte=00, 00 |
Appreciate
1
///M Houbi1672.00 |
06-01-2018, 12:16 AM | #7 | |
Enlisted Member
6
Rep 39
Posts |
Quote:
|
|
Appreciate
0
|
11-01-2019, 06:51 AM | #9 |
First Lieutenant
66
Rep 348
Posts |
Any update on if this is working? I have a 2020 if that helps.
__________________
Pure800 - DS2 HPFP - Nostrum S1 - ER Catless DP - Remus Non-Resonated Catback - BM3 Flex Fuel Kit - Ross V1 VTA PCV - Custom Tunes on MHD/BM3 - xHP Stage 3 - TCKline SA/DA Coils - Apex ARC8s - Vicrez Carbon Fiber CSL Trunk - ALP Laser System - Escort Max 360c with Blendmount + more... | IG: kianf22 |
|
Appreciate
0
|
11-14-2019, 03:02 PM | #10 |
Enlisted Member
18
Rep 45
Posts |
Hi,
I have the first "global" value listed below in BimmerCode but I do not have the 2nd of 3rd . Can anyone advise as to how to get this to work? 3000 SM_GLOBAL -> EINAUSSTIEGSHILFE = Modus_FA_SLV 3012 EAH -> EAH_VERFAHRWEG_SLV_PHYS = Werte=00, 64 3012 EAH -> EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS = Werte=00, 00 |
Appreciate
0
|
12-12-2019, 05:46 PM | #11 | |
New Member
3
Rep 12
Posts |
Quote:
Any help would be appreciated! |
|
Appreciate
0
|
12-12-2019, 07:07 PM | #12 | ||
Luxury at the redline :)
9118
Rep 7,563
Posts |
Quote:
When I attempted to recode the Easy Exit/Entry, initially, it also was not working. Funny, I then got tired of messing with it and left. The next morning it worked fine. I suspected that when the battery is close to being drained, it's doesn't commence. Double check the parameters, code it in again, then power down the vehicle and let it go to 'sleep mode,' then retry it. This might solve your issue. I also notice then when try to retract and detract the seats with the physical control, after a certain distance, it stops and you have repress the button to get it going again. I guess this must be a safety feature they implemented via the new software integration. Do you happen to know the iStep version was uploaded to your vehicle? |
||
Appreciate
0
|
12-13-2019, 10:36 PM | #13 | |
New Member
3
Rep 12
Posts |
Quote:
I'll see if it has taken effect tomorrow. I spent about half an hour trying to get it to work. I don't think it has anything to do with the battery though because by the time i was coding, I had already driven for around 2 hours. And not sure of the iStep version. How can I check? |
|
Appreciate
0
|
12-14-2019, 06:56 PM | #15 | ||
Luxury at the redline :)
9118
Rep 7,563
Posts |
Quote:
I'm not sure why it's not working, I coded a 2018 3 series and it activated fine. All I could say is triple check the coding and try again. I ran out of suggestions.. Sorry. |
||
Appreciate
0
|
12-15-2019, 02:24 PM | #16 | |
New Member
3
Rep 12
Posts |
Quote:
The chair goes back the full 100mm even though I had changed the value from 64 to 32 but I'll play around with the setting again. Thanks again for the help |
|
Appreciate
1
aerodavew10.50 |
12-15-2019, 05:18 PM | #17 | ||
Luxury at the redline :)
9118
Rep 7,563
Posts |
Quote:
Yea, mines I had coded severals time, right after a firmware update and it still didn't work after hours of trying.. I gave up because the car indicated that the battery was getting drained, so I just accepted that new software ate the old hack feature. The next morning, as jumped in and the seat started moving forward, 'I was WTF' but whatever. : Maybe someone one day will solve this mystery. |
||
Appreciate
0
|
12-24-2019, 12:05 PM | #18 |
Everyday I'm shuffling
451
Rep 1,098
Posts |
|
Appreciate
0
|
01-07-2020, 02:35 PM | #19 | |
Private First Class
94
Rep 147
Posts |
For anyone in doubts, I’ve coded easy entry exactly as per Poochie:
Quote:
I also had 3015 EAH instead of 3012. My car is a 2017. My I-Level is F020-18-11-531 After coding the car I locked it, unlocked, turned it on and moved it on my driveway. After I shut it off and locked it, the seat had retracted by itself. Now it works 😎 |
|
Appreciate
1
Poochie9118.00 |
01-07-2020, 03:21 PM | #20 | |
Everyday I'm shuffling
451
Rep 1,098
Posts |
Quote:
3012 EAH does not have EAH_VERFAHRWEG_SLV_PHYS nor EAH_SCHUTZFREIRAUM_HINTEN_SLV_PHYS parameters under it. Would be interested in knowing what others have done. |
|
Appreciate
0
|
03-18-2020, 09:45 PM | #21 | |
New Member
0
Rep 7
Posts |
Worked great
Quote:
|
|
Appreciate
0
|
03-20-2020, 01:53 PM | #22 |
Everyday I'm shuffling
451
Rep 1,098
Posts |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|