F22 coding cheat sheet

bman6074 · 01-16-2015, 02:24 PM

Quote:

Originally Posted by pikcachu

i think eco pro over rides it.... does the light go back on when you switch back to comfort?

Nope :/

bman6074 · 01-16-2015, 02:26 PM

Quote:

Originally Posted by Shankska

yeah just dont go into eco pro and its win win. auto start/stop stays off and you dont drive a 1 cylinder

True, I don't use it often but was hoping not have to worry about auto start/stop when I switched from different modes. A friend uses eco pro mode every day and was hoping to have it off and start the car in eco pro mode.

pikcachu · 01-16-2015, 02:36 PM

Quote:

Originally Posted by bman6074

Nope :/

ya i think the code only applies when you start the car.... so if you switch to eco pro and shut off when you turn the car back on, the light should be on

Bimmer86 · 01-19-2015, 07:56 AM

You should add the high beam assist codes to update the speed that it enables/disables to the cheat sheet. I changed it to 15MPH/25MPH.

C_HBA_ENA_V_LO werte=18 (15 MPH)
C_HBA_ENA_V_HI werte=28 (25 MPH)

There is also C_HBA_HGWY_V_LO and C_HBA_HGWY_V_HI but I still don't know what it actually does.

Bimmer86 · 01-19-2015, 08:09 AM

It was kind of odd that even though I updated the VO, I still had to update the FDL's. Not sure if the VO's just wasn't related to them, but nonetheless it works great now.

I also updated these for the HBA:

FLA / 3000 / Lucid_Nominal_TL_width - Lucid (7D)
FLA / 3000 / Lucid_Nominal_HL_width - Lucid (73)
FLA / 3000 / Lucid_Image_Height - Lucid (7A)
FLA / 3000 / Lucid_HL_Height - Lucid (40)
FLA / 3000 / LucidHoodLength - Lucid (A0)
FLA / 3001 / DFL_Vehicle 0 - Verbaut

pikcachu · 01-19-2015, 03:49 PM

Quote:

Originally Posted by Bimmer86

You should add the high beam assist codes to update the speed that it enables/disables to the cheat sheet. I changed it to 15MPH/25MPH.

C_HBA_ENA_V_LO werte=18 (15 MPH)
C_HBA_ENA_V_HI werte=28 (25 MPH)

There is also C_HBA_HGWY_V_LO and C_HBA_HGWY_V_HI but I still don't know what it actually does.

cool added those

pikcachu · 01-19-2015, 03:52 PM

Quote:

Originally Posted by Bimmer86

It was kind of odd that even though I updated the VO, I still had to update the FDL's. Not sure if the VO's just wasn't related to them, but nonetheless it works great now.

I also updated these for the HBA:

FLA / 3000 / Lucid_Nominal_TL_width - Lucid (7D)
FLA / 3000 / Lucid_Nominal_HL_width - Lucid (73)
FLA / 3000 / Lucid_Image_Height - Lucid (7A)
FLA / 3000 / Lucid_HL_Height - Lucid (40)
FLA / 3000 / LucidHoodLength - Lucid (A0)
FLA / 3001 / DFL_Vehicle 0 - Verbaut

so you updated you VO, but did you VO code any of the ECU's??? you probably need to VO code FEM_BODY and FLA... else just updating your VO does nothing in terms of coding... just specifies what options your car has...

Bimmer86 · 01-20-2015, 07:50 AM

Quote:

Originally Posted by pikcachu

so you updated you VO, but did you VO code any of the ECU's??? you probably need to VO code FEM_BODY and FLA... else just updating your VO does nothing in terms of coding... just specifies what options your car has...

Ooh I see, so that's what the last page of the PDF was for. I thought it was an optional step for if I was changing the CAFD version in the ECU or something like that, since I was reading about that as well (my car had ECU versions that was not in the latest PSDZDATA so I was looking at how to resolve it until I found the new CAFD files that Shawn posted somewhere).

I'll recode it at some point but everything seems to be working great for now.

BTW, I'm sure this is probably a continuing discussion somewhere, but what do you know about the CAFD files being trimmed? Say if the car was updated by the dealer, would injecting a previous CAFD into the ECU be an easy solution, or would that cause all sorts of other issues?

shawnsheridan · 01-20-2015, 08:59 AM

Quote:

Originally Posted by Bimmer86

...BTW, I'm sure this is probably a continuing discussion somewhere, but what do you know about the CAFD files being trimmed? Say if the car was updated by the dealer, would injecting a previous CAFD into the ECU be an easy solution, or would that cause all sorts of other issues?

It is possible, but you are limited by the firmware (SWFL) in what CAFD you can inject, so older, untrimmed CAFD may not even be an option.

Bimmer86 · 01-20-2015, 08:52 PM

Quote:

Originally Posted by pikcachu

cool added those

BTW, you have the description reverse, accelerating to HI is the speed that HBA is enabled, and decelerating to LO is the speed that HBA is disabled

pikcachu · 01-20-2015, 10:17 PM

Quote:

Originally Posted by Bimmer86

BTW, you have the description reverse, accelerating to HI is the speed that HBA is enabled, and decelerating to LO is the speed that HBA is disabled

cool fixed thanks

Delnari · 01-21-2015, 08:24 AM

Is ASD coding for S55 engine sound ready to be added to the coding sheets yet? Need code for HK sound system and for HiFi sound system. Thanks!

Bimmer86 · 01-21-2015, 08:51 AM

Quote:

Originally Posted by Delnari

Is ASD coding for S55 engine sound ready to be added to the coding sheets yet? Need code for HK sound system and for HiFi sound system. Thanks!

Haha, well that certainly escalated quickly. Nonetheless, changing just the model with the matching engine should do the trick.

pikcachu · 01-21-2015, 11:08 AM

Quote:

Originally Posted by Delnari

Is ASD coding for S55 engine sound ready to be added to the coding sheets yet? Need code for HK sound system and for HiFi sound system. Thanks!

There is a setting for "audio level" that lets you choose:

Stereo = 00
Hifi = 01
Branded Hifi = 02
TopHifi / Branded TopHifi = 03
High End = 04

I don't have HK so can't try it

Viffermike · 01-21-2015, 04:14 PM

There are a few of us on the forum who want to install LED bulbs in the taillight housing, but because of voltage anomalies between LEDs and incandescents, the ECU's bulb self-check causes LED bulbs to flicker at startup -- and some report flickering during vehicle operation, too.

Supposedly the E30 can be coded to disable this self-check. Has anybody figured out if the same (or a similar) code disables the bulb self-check on an F22? I didn't see the option on pikcachu's cheat sheet, so ... ?

pikcachu · 01-21-2015, 05:24 PM

Quote:

Originally Posted by Viffermike

There are a few of us on the forum who want to install LED bulbs in the taillight housing, but because of voltage anomalies between LEDs and incandescents, the ECU's bulb self-check causes LED bulbs to flicker at startup -- and some report flickering during vehicle operation, too.

Supposedly the E30 can be coded to disable this self-check. Has anybody figured out if the same (or a similar) code disables the bulb self-check on an F22? I didn't see the option on pikcachu's cheat sheet, so ... ?

if you can get the code to do it on the F30 I can check ... should be similar

Bimmer86 · 01-21-2015, 06:38 PM

Quote:

Originally Posted by pikcachu

if you can get the code to do it on the F30 I can check ... should be similar

I have this for the turn signals

Module Section Function Value Default Comment
FEM_BODY 3061 FRA_V_L_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Left Turn Signal Bulb Cold Monitoring
FEM_BODY 3061 FRA_V_L_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Left Turn Signal Bulb Warm Monitoring
FEM_BODY 3061 FRA_V_L_IS_LED aktiv nicht_aktiv Enables Front-Left LED bulb
FEM_BODY 3061 FRA_V_R_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Right Turn Signal Bulb Cold Monitoring
FEM_BODY 3061 FRA_V_R_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Right Turn Signal Bulb Warm Monitoring
FEM_BODY 3061 FRA_V_R_IS_LED aktiv nicht_aktiv Enables Front-Right LED bulb
FEM_BODY/REM 3061 FRA_H_L_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Left Turn Signal Bulb Cold Monitoring
FEM_BODY/REM 3061 FRA_H_L_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Left Turn Signal Bulb Warm Monitoring
FEM_BODY/REM 3061 FRA_H_L_IS_LED aktiv nicht_aktiv Enables Rear-Left LED bulb **May cause Check Engine Light**
FEM_BODY/REM 3061 FRA_H_R_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Right Turn Signal Bulb Cold Monitoring
FEM_BODY/REM 3061 FRA_H_R_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Right Turn Signal Bulb Warm Monitoring
FEM_BODY/REM 3061 FRA_H_R_IS_LED aktiv nicht_aktiv Enables Rear-Right LED bulb **May cause Check Engine Light**

http://f30.bimmerpost.com/forums/sho....php?t=1020138

pikcachu · 01-21-2015, 10:16 PM

Quote:

Originally Posted by Bimmer86

I have this for the turn signals

Module Section Function Value Default Comment
FEM_BODY 3061 FRA_V_L_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Left Turn Signal Bulb Cold Monitoring
FEM_BODY 3061 FRA_V_L_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Left Turn Signal Bulb Warm Monitoring
FEM_BODY 3061 FRA_V_L_IS_LED aktiv nicht_aktiv Enables Front-Left LED bulb
FEM_BODY 3061 FRA_V_R_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Right Turn Signal Bulb Cold Monitoring
FEM_BODY 3061 FRA_V_R_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Front-Right Turn Signal Bulb Warm Monitoring
FEM_BODY 3061 FRA_V_R_IS_LED aktiv nicht_aktiv Enables Front-Right LED bulb
FEM_BODY/REM 3061 FRA_H_L_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Left Turn Signal Bulb Cold Monitoring
FEM_BODY/REM 3061 FRA_H_L_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Left Turn Signal Bulb Warm Monitoring
FEM_BODY/REM 3061 FRA_H_L_IS_LED aktiv nicht_aktiv Enables Rear-Left LED bulb **May cause Check Engine Light**
FEM_BODY/REM 3061 FRA_H_R_KALTUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Right Turn Signal Bulb Cold Monitoring
FEM_BODY/REM 3061 FRA_H_R_WARMUEBERWACHUNG nicht_aktiv aktiv Turns off Rear-Right Turn Signal Bulb Warm Monitoring
FEM_BODY/REM 3061 FRA_H_R_IS_LED aktiv nicht_aktiv Enables Rear-Right LED bulb **May cause Check Engine Light**

http://f30.bimmerpost.com/forums/sho....php?t=1020138

Ok looked at the F22 cafd and this is what I found:

FRONT
LED on

TFL
POL
SML
FRA_Z
LCI_0
LCI_1
LCI_3
LCI_4
LCI_5
LCI_6
LCI_7
LCI_8

LED off

AL
FL
NSW
FRA_V
BIX
LCI_2

REAR
LED on

SL
KZL single no L/R
BL_M single no L/R

LED off

SL_2
BL
BFD
NSL
RFS
FRA_H

So in the back the entries that have the LED off (meaning its incandescent light instead, are the ones in red)

not sure what each name means cause the comments don't say anything about it so probably SL_2 BL BFD NSL RFS FRA_H are abbreviations in german

but probably if you code KAULT, WARM to nitch_aktive and IS_LED to aktiv for each of those SL_2 BL BFD NSL RFS FRA_H , it should disable the warning light

pikcachu · 01-22-2015, 02:02 AM

looks like coding days might be counted

http://www.bimmerfest.com/forums/sho...d.php?t=812652

mvallido · 01-22-2015, 02:09 AM

Quote:

Originally Posted by pikcachu

looks like coding days might be counted

http://www.bimmerfest.com/forums/sho...d.php?t=812652

Oh No!

pikcachu · 01-22-2015, 02:16 AM

need to hurry to test that F80 engine sound

1stm235i · 01-22-2015, 04:39 AM

Quote:

Originally Posted by pikcachu

need to hurry to test that F80 engine sound

pls...... Do it ASAP 😜 thanks

01-19-2015, 07:56 AM	#510
Bimmer86 Private First Class 74 Rep 177 Posts Drives: 2024 M440i xDrive Gran Coupe Join Date: Dec 2014 Location: Northern Virginia iTrader: (0)	You should add the high beam assist codes to update the speed that it enables/disables to the cheat sheet. I changed it to 15MPH/25MPH. C_HBA_ENA_V_LO werte=18 (15 MPH) C_HBA_ENA_V_HI werte=28 (25 MPH) There is also C_HBA_HGWY_V_LO and C_HBA_HGWY_V_HI but I still don't know what it actually does.
	Appreciate 0 Quote

01-19-2015, 08:09 AM	#511
Bimmer86 Private First Class 74 Rep 177 Posts Drives: 2024 M440i xDrive Gran Coupe Join Date: Dec 2014 Location: Northern Virginia iTrader: (0)	It was kind of odd that even though I updated the VO, I still had to update the FDL's. Not sure if the VO's just wasn't related to them, but nonetheless it works great now. I also updated these for the HBA: FLA / 3000 / Lucid_Nominal_TL_width - Lucid (7D) FLA / 3000 / Lucid_Nominal_HL_width - Lucid (73) FLA / 3000 / Lucid_Image_Height - Lucid (7A) FLA / 3000 / Lucid_HL_Height - Lucid (40) FLA / 3000 / LucidHoodLength - Lucid (A0) FLA / 3001 / DFL_Vehicle 0 - Verbaut
	Appreciate 0 Quote

01-21-2015, 08:24 AM	#518
Delnari Major 258 Rep 1,040 Posts Drives: 2014 MG F22 Auto Join Date: Mar 2010 Location: Alexandria, VA iTrader: (2)	Is ASD coding for S55 engine sound ready to be added to the coding sheets yet? Need code for HK sound system and for HiFi sound system. Thanks!
	Appreciate 0 Quote

01-21-2015, 04:14 PM	#521
Viffermike Colonel 1756 Rep 2,942 Posts Drives: '18 black-n-blue 718 Cayman Join Date: Jan 2015 Location: Big D iTrader: (0)	There are a few of us on the forum who want to install LED bulbs in the taillight housing, but because of voltage anomalies between LEDs and incandescents, the ECU's bulb self-check causes LED bulbs to flicker at startup -- and some report flickering during vehicle operation, too. Supposedly the E30 can be coded to disable this self-check. Has anybody figured out if the same (or a similar) code disables the bulb self-check on an F22? I didn't see the option on pikcachu's cheat sheet, so ... ?
	Appreciate 0 Quote

01-22-2015, 02:02 AM	#525
pikcachu Major General 1412 Rep 5,262 Posts Drives: M235i (F22 Red angel) Join Date: Jul 2011 Location: undisclosed iTrader: (1)	looks like coding days might be counted http://www.bimmerfest.com/forums/sho...d.php?t=812652
	Appreciate 0 Quote

01-22-2015, 02:16 AM	#527
pikcachu Major General 1412 Rep 5,262 Posts Drives: M235i (F22 Red angel) Join Date: Jul 2011 Location: undisclosed iTrader: (1)	need to hurry to test that F80 engine sound
	Appreciate 0 Quote